two-stage general purpose rfi power line filter the dual t section rfi power line filters provide premium performance at moderate cost. they are well suited for low impedance loads where noisy rfi environments are present. they control pulsed, continuous and/or intermittent interference, providing protection to your equipment from power line noise in addition to protecting the line from equipment noise. the r series dual t type provides low leakage current without deterioration of insertion loss characteristics and at a competitive cost. the er models meet the low leakage current requirements of vde portable equipment, and (120 volt) ul2601 non-patient medical equipment. specifications maximum leakage current,each line-to-ground vr models er models @ 120 vac 60 hz: .4 ma .21 ma @ 250 vac 50 hz: .7 ma .36 ma hipot rating (one minute): line-to-ground 2250 vdc line-to-line 1450 vdc operating frequency: 50/60 hz rated voltage (max.): 250 vac minimum insertion loss in db: line-to-ground in 50 ohm circuit current frequencyChz rating .15 .5 1 5 10 30 vr models 1a, 3a 30 65 65 65 65 65 2a, 5a, 10a, 20a 5 44 60 65 65 60 er models 1a, 3a 25 60 65 65 65 65 2a, 5a, 10a, 20a 2 35 51 63 60 50 line-to-line in 50 ohm circuit current frequencyChz rating .15 .5 1 5 10 30 vr, er models 1a, 3a C C 65 60 54 46 2a, 5a, 10a, 20a C C 35 60 57 45 84 catalog 1654001 dimensions are in inches and dimensions are shown for usa cust. svc.: 1-800-468-2023 www.corcom.com revised 05-07 millimeters unless otherwise reference purposes only. corcom prods: 1-847-680-7400 www.tycoelectronics.com specified. values in italics specifications subject germany: 49-89-6089-0 are metric equivalents. to change. r series r series corcom product guide electrical schematic resistor location for reference only. 1 0vr6 v r7/er7 vr1/er1 vr3/er3 case style 20vr6 note: same layout for 20vr1 and 20er1, except .250 [ 6.35 ] (5) terminals replace screw terminals of 20vr6. torque 18 2 in.lb ul recognized csa certified vde approved line load e db 2.00 50.8 a terminals: no. 8-32 (5) c slots: .250 6.35 .156 3.96 x (4)
two-stage general purpose rfi power line filter (continued) case dimensions abc d e .015 p art no. (max) (max) (max) (max) .38 1vr1, 1er1, 3.35 1.81 1.16 2.375 2.78 2VR1, 2er1 85.1 46.0 29.5 60.33 70.6 1vr3, 1er3, 2.07 1.81 1.16 2.375 2.78 2vr3, 2er3 52.6 46.0 29.5 60.33 70.6 3vr1, 3er1, 3.85 2.07 1.16 2.938 3.35 5vr1, 5er1 97.8 52.6 29.5 74.63 85.1 3vr3, 3er3, 2.56 2.07 1.16 2.938 3.35 5vr3, 5er3 65.0 52.6 29.5 74.63 85.1 3vr7, 3vr7m, 4.33 2.25 1.28 1.575 0.64 3er7, 3er7m 110.0 57.2 32.5 40.01 16.3 5vr7, 5vr7m, 4.33 2.25 1.28 1.575 0.64 5er7, 5er7m 110.0 57.2 32.5 40.01 16.3 10vr1, 10er1 3.85 2.07 1.53 2.938 3.35 97.8 52.6 38.9 74.63 85.1 10vr3, 10er3 2.56 2.07 1.53 2.938 3.35 65.0 52.6 38.9 74.63 85.1 10vr6 3.96 2.07 1.53 2.938 3.35 100.6 52.6 38.9 74.63 85.1 10vr7, 10vr7m, 4.33 2.25 1.53 1.575 0.88 10er7, 10er7m 110.0 57.2 38.9 40.01 22.4 20vr1, 20er1 5.23 3.37 1.53 3.75 4.20 20vr6 132.8 85.6 38.9 95.25 106.7 85 catalog 1654001 dimensions are in inches and dimensions are shown for usa cust. svc.: 1-800-468-2023 www.corcom.com revised 05-07 millimeters unless otherwise reference purposes only. corcom prods: 1-847-680-7400 www.tycoelectronics.com specified. values in italics specifications subject germany: 49-89-6089-0 are metric equivalents. to change. r f i p o w e r l i n e f i l t e r s r series corcom product guide case styles part numbers 0 1vr1 0 1er1 0 1vr3 0 1er3 0 2VR1 0 2er1 0 2vr3 0 2er3 0 3vr1 0 3er1 0 3vr3 0 3er3 0 3vr7 0 3er7 0 3vr7m 0 3er7m 0 5vr1 0 5er1 0 5vr3 0 5er3 0 5vr7 0 5er7 0 5vr7m 0 5er7m 10vr1 10er1 10vr3 10er3 10vr6 10er7 10vr7 10er7m 10vr7m 20er1 20vr1 20vr6 line cord (r7/r7m): ga400 r1 (except 20 amp) typical dimensions: terminals: .250 [ 6.35 ] (5) holes: .07 [ 1.8 ] dia.(4) mounting holes: .188 [ 4.78 ] dia. (2) slot: .07 x .16 [ 1.8 x 4.1 ] r3 typical dimensions: wire leads: 4.0 [ 101.6 ] min. mounting holes: .188 [ 4.78 ] dia. (2) torque: 18 2 in.lb r7 & r7m (with metric insert) 10vr6 typical dimensions: terminals: .250 [6.35 ] (5) holes: .07 [ 1.8 ] dia.(4) mounting holes: .188 [ 4.78 ] dia. (2) slot: .07 x .16 [ 1.8 x 4.1 ] ? .02 [ .5 ] ? ? ? tolerance .005 [ 0.13 ] panel cutout (back mount) d e a c b a d e c b brown blue brown blue green/ yellow c b e d a terminals: no. 8-32 (5) mounting holes .188 [4.78] dia. (2) a tapped insert: d b e c .235 5.96 1.575 40.01 .157 3.98 .910 23.11 dia. (2) 1.295 32.89 r no. 6-32 x 1/4 (2)-r7 no. m-3 x .5 (2)-r7m
|
